ID meets OD
The receiving section’s inside diameter must be considered against the next section’s outside diameter, including tolerances and any wear guides.
Images show configuration references. Final appearance is agreed with your sample.
FACTORY DIRECT / MADE TO YOUR SPECIFICATION
Carbon fibre
water-fed poles.
Any custom extended length from 6 to 20 metres. Configure the tubes, clamps and brush connection around your equipment.
6–20 mAny length in this range
19.7–65.6 ftApprox. extended pole length
01 / Tube dimensions & layup02 / Connections & machining03 / Clear supply scope
Quoted to your build.
Configure your enquiry ↓View full specifications ↗Price is based on dimensions, material, quantity and accessories. Share the specification below to start a technical enquiry.
BUILD YOUR ENQUIRY
A few details.
A clearer quotation.
Choose any length between 6 and 20 m, including intermediate lengths such as 9.5 m. The feet value updates automatically.
This prepares your enquiry details. It does not place an order or send a message.
WATER-FED POLES / SPECIFICATIONS
Specify the pole around your cleaning task.
| Parameter | Custom specification |
|---|---|
| Extended pole length | Any custom length from 6–20 m / approx. 19.7–65.6 ft |
| Construction | Nested carbon fibre round tubes with matched sliding fits |
| Section count & closed length | Configured for the requested extended length, transport length and overlap |
| Tube OD, ID & wall | Custom dimensions; final tube schedule agreed before production |
| Clamps | Lever-clamp layout and colour to be agreed with the selected design |
| Brush connection | Connection dimensions and brush or angle-adaptor requirements to drawing or sample |
| Water hose | Internal or external route to be specified; hose bore and fittings agreed for the system |
| Finish | Gloss or matt finish; appearance sample to be approved |
| Weight & stiffness | Dependent on length, tube layup and accessories; confirmed for the selected build |
| Supply scope | Bare tube sections, machined components or an assembly with agreed accessories |
| Machining | Cutting, drilling and connector preparation to approved drawings |
Brushes, hoses, clamps and adaptors are included only when listed in the quotation. Images illustrate configurations; they do not establish a tested load or compatibility rating.
WORKSHOP / TUBE FIT
A telescopic pole is a matched tube system.
Overlap is structural
The joint must retain its designed overlap when extended. Mark the agreed extension limit; do not recover extra reach by reducing overlap without a design review.
Clamps are part of the design
Specify the clamp contact zone, required holding behaviour and permitted local compression. Tightening a clamp harder is not a substitute for a suitable fit.
Check the clearance arithmetic.
Use the receiving tube’s inside diameter and the sliding tube’s outside diameter. The example values are for explanation, not a recommended fit.
Minimum clearance uses the smallest receiving ID and largest sliding OD. Maximum clearance does the reverse.
This calculation does not approve an assembly. Ovality, straightness, surface finish, wear, temperature, overlap and the clamp design also affect fit and service performance.
WORKSHOP / QUOTE DETAILS
Specify the complete assembly.
Dimensions in millimetres unless shown otherwise. Scroll sideways on a small screen.
| Item | Confirm for your enquiry |
|---|---|
| Length | Required actual extended length and transport / closed length |
| Sections | Count, individual lengths, diameters, wall and retained overlap |
| End tool | Brush and neck mass, attachment geometry and operating orientation |
| Water route | Hose routing, fittings and required spare hose when extended |
| Finish & wear | External finish, sliding surfaces, guides, stops and clamp zones |
| Acceptance | Sample fit, joint security and agreed deflection / durability tests |
Take the next step.
MORE APPLICATIONS / SAME MANUFACTURING KNOW-HOW
Match the pole to the job.
FROM REQUIREMENT TO PRODUCTION
Know what you are approving.
Agree the specification
Confirm dimensions, intended use, mating interfaces, quantity and which accessories are included.
Check the actual build
Agree sample requirements and acceptance checks for fit, finish, dimensions and the relevant assembly behaviour.
Confirm the supply terms
Review tooling or sample costs, production price, lead time, packing and delivery terms before placing an order.
LET’S MAKE IT CLEAR.
What are
you building?
You don’t need a complete specification to start a conversation. Tell us the application and what you know so far.
sales@fibreparts.com ↗